GUIDE TO FITTING YOUR COLOUR KIT: ASETEK SIMSPORTS FORTE & LA PRIMA WHEELS

· Torx Wrench Keys : T10 (3mm) and T15

   (4mm). If you do not have these you can

   purchase these from our shop for £7    

   (£5 if ordered with the colour kit).

· Cloth or soft area (to protect and rest your

   steering wheel on).
 

· Asetek's Plastic tweezers that were supplied

  with your wheel (thank you Asetek!). Do not

  use metal tweezers as there is a risk of 

  damaging your colour kit parts or wheel
 

· Small container to keep all your removed

  screws etc safe. 

· Colour Kit parts (including some spares)

·  Time to transform the accents on your 

   wheel to another colour.

·  Place the Wheel carefully face down onto

   your soft surface (or cloth).

·  Remove the paddle by unscrewing the

   retained M3 screw using a T10 (3mm) Torx

   Wrench Key.

·  IMPORTANT! Try to keep the Torx Wrench 

   Key away from the paddle magnet (as it 

   easily scratches the magnet surface)

 · If using your own Torx Wrench Key, make sure

   the fit is good as these screws may be

   tight the first time of loosening. A poor fitting

   Torx Wrench Key can result in you rounding

   the hole on the top of the screw head.

 · Repeat for the other paddle.

· Remove the four M4 x 10mm long

  Countersunk Head Torx Screws from the grip

  using a T15 (4mm) Torx Wrench Key.

·  If using your own Torx Wrench Key, make sure

   the fit is good as these screws may be

   tight the first time of loosening. A poor fitting

   Torx Wrench Key can result in you rounding

   the hole on the top of the screw head.

 · Repeat for other grip.

· The part is silicone rubber and very flexible.

· Feed this carefully off the metal section of your 

   grip.

· The part is silicone rubber and very flexible.

· Feed this carefully off the metal section of your 

  grip.

· Repeat steps 3 to 4 for the other grip.

· Push the part in between the rubber

  and the metal bracket as shown. 

· IMPORTANT! Make sure the part is orientated

  so that the radius edge is on the metal bracket

  side. 

·  Make sure the part is centrally positioned as

   shown.

· IMPORTANT! Make sure the Large U-shaped

  part is orientated so that the sloped part is on

  the same side as the radius shape of the 

  block part. If the u-shaped part is the wrong

  way up, the part will not engage properly 

  (as the pips are not centrally positioned)

· Place your finger behind the block part as

  shown and with the U-shaped part, slide this

  onto the sides. The two pips either side of the

  U-shaped part will engage into the side holes

  of the block part.

· Push the u-shaped part until flush.

 ·   Make sure the u-shaped part is fully

     engaged on both sides. It should look like 

     the photo.

 ·  Repeat steps 5 to 9 for the other grip.

· Orientate the small u-shaped part as shown

  and snap this part over the metal bracket (on

  the grips middle section). Note: The part is 

  symmetrical.

· It should look like this if snapped on the

  correct way round in relation to the metal

  bracket.

· IMPORTANT! Make sure the small rectangular

  part is orientated as shown on the photo.

· Place your finger behind the small u-shaped

  part as shown and with the small rectangular

  part, slide this into one side of the the gap and

  snap into place.

 · Repeat steps 10 to 12 for the other grip.  

· Position the grip as shown.

· Re-screw the four M4 x 10mm long

  Countersunk Head Torx Screws into the grip

  using a T15 (4mm) Torx Wrench Key.

 · Repeat for the other grip.

· Re-fit the paddle using a T10 (3mm) Torx

  Wrench Key as shown.

· Repeat for other paddle.

· Using your Asetek plastic tweezers, apply one 

  of the black 11mm dia. protection stickers.

· Repeat for the other paddle.

· Using your Asetek plastic tweezers, remove

  the backings from the four button caps'

  adhesive pads.

·  Attach each of the four button caps over the

   orange buttons on the wheel as shown. 

   Press home firm for the high tack adhesive to

   "key" onto the button.

· Using your Asetek plastic tweezers, apply the

  black sticker to cover the orange brushed

  aluminium face (as shown). This may take a

  few attempts to align correctly so be patient.

· Repeat for the other side of the Quick Release

  with a second sticker.

Congratulations! Your installation and wheel transformation is now complete.

If you need to remove the Large or Small Coloured Infill assemblies again, please use the Asetek plastic tweezers carefully to do so.